查看“CMTS”的源代码

== DEBUG ==
=== RPD can not online ===
sho cable  depi  multicast pool
sho cable  rpd log   reverse
== SSH Configuration ==
ip ssh V1
configure terminal
enable password lab
ip domain-name cisco.com
crypto key generate rsa general-keys modulus 1024
ip ssh time 120
ip ssh authentication 4
line vty 0 4
transport input ssh
exit
aaa new-model
aaa authentication login default local
username admin password lab

ip ssh V2
1.    enable

2.    configure terminal

3.    ip ssh rsa keypair-name keypair-name


4.    crypto key generate rsa usage-keys label ssh_key modulus 1024
5.    ip ssh [time-out seconds | authentication-retries integer]


6.    ip ssh version 2
ip ssh authentication-retries 4
ip ssh source-interface GigabitEthernet0
ip ssh rsa keypair-name ssh_key
ip ssh version 2
ip ssh server algorithm encryption aes128-ctr aes192-ctr aes256-ctr
ip ssh client algorithm encryption aes128-ctr aes192-ctr aes256-ctr


aaa new-model
aaa authentication login default local
aaa session-id common

username admin password lab
line vty 0 4
 exec-timeout 0 0
 privilege level 15
 password lab
 logging synchronous
 exec prompt timestamp
 transport input ssh
== vCMTS ==
=== ptp ===
vcmts config
1.ptp config
[RP_0:~]$ cat /harddisk/rommon_vars
SR_INIT_SHELL=aux_do_system_shell
IP_ADDRESS=3.33.11.23
IP_SUBNET_MASK=255.255.0.0
DEFAULT_GATEWAY=3.33.0.1
REAL_MGMTE_DEV=
SR_MGMT_VRF=0
RPHY_IF=Gi2
CABLE_PTP_IF=eth3
CABLE_PTP_IP=3.30.222.2
CABLE_PTP_MASK=255.255.0.0
CABLE_PTP_SERVER=192.168.222.222
refer:http://cmtswiki.cisco.com:8080/display/cmtspub/PTP+setup+in+vCMTS+VM+and+server
[Router:~]$ cat /harddisk/ptpd2.conf   
ptpengine:interface=eth3
ptpengine:domain=0
ptpengine:preset=slaveonly
ptpengine:ip_mode=unicast
ptpengine:unicast_negotiation=y
ptpengine:unicast_destinations=192.168.222.222
ptpengine:log_delayreq_interval=0
global:dump_packets=N
global:log_status=y
global:status_file=/bootflash/ptpd2.status
global:log_file=/bootflash/ptpd2.log
global:log_file_max_size=256
ptpengine:vbr_ignore_utc_offset=y
ptpengine:utc_offset=0

2.vmac config
[RP_0:~]$ cat /harddisk/vmac_config_file
./vmac -nhop_mac 00:04:9F:00:09:13 -rphy_ip 3.35.1.4 -vmac_mac 00:50:56:a4:13:15 -vmac_ip 3.35.1.1  -rphy_if Gi2 --us_mac_cpus 1 --ds_mac_cpus 2 --debug 0
refer:http://cmtswiki.cisco.com:8080/display/cmtspub/vmac+related+setup
3.
cable rpd 1
identifier 0004.9f00.0913
core-interface Gi2
  principal
  rpd-ds 0 downstream-cable 0/0/0 profile 3
  rpd-us 0 upstream-cable 0/0/0 profile 3
r-dti 1
rpd-event profile 0
!
ptp r-dti 1
ptp-domain 0
clock-port 1
   ethernet 1
   clock source ip 192.168.222.222 gateway ip 3.35.222.222               /*   ip address of PTP server  and ip address of RPD gateway (vhh0 in my case uses local ip address of RPD)
!
0050.5691.2540   


rpd config
1.ptp config
root@00049F000913:/# cat /bootflash/ptp.conf
[PORT_ID] 0
[MASTER_IP] 192.168.222.222
[GATEWAY_IP] 3.35.222.222

R-PHY#show ptp clock 0 state
apr state       : PHASE_LOCK
clock state     : SUB_SYNC
current tod     : 1479943078   Wed Nov 23 23:17:58 2016
active stream   : 1
==stream    1   :
  port id       :                0
  master ip     :  192.168.222.222
  stream state  :       PHASE_LOCK
  Master offset :               44
  Path    delay :            -1671
  Forward delay :            -1627
  Reverse delay :            -1695
  Freq offset   :          -455301
  1Hz  offset   :               14
refer: http://cmtswiki.cisco.com:8080/display/cmtspub/PTP+config+in+RPD


ssh -l root 3.35.1.4
00:04:9F:00:09:13/3.35.1.4
en
shell
upgradeuboot.sh
tftp -r /tftpboot/RPD_ECE3-20161109_070001.itb -g 20.1.0.33
tftp -r /tftpboot/RPD_seres_rpd_20170112_010001.itb -g 3.35.11.1
tftp a0000000 3.33.11.1:/tftpboot/RPD_seres_rpd_20160912_010001.itb && bootm
tftp a0000000 3.33.11.1:/tftpboot/RPD_ECE3-20161110_070002.itb && bootm
ifconfig eth2 3.33.11.5 netmask 255.255.0.0
tftp -r tftpboot/RPD_ECE3-20161110_070002.itb -g 3.33.11.1

Check uboot version
root@RPD00049f300255:/# strings -n 30 /dev/mtd5 | grep ^U-Boot
U-Boot 2016.01 (Sep 23 2016 - 03:19:57 +0800)
Check CPLD version
root@00049F300249:/# rpdcpld -g 0
address = 0x0, value = 0x235
ns-cBR-05#sho running-config | sec ptp
ptp clock ordinary domain 0   
 servo tracking-type R-DTI
 clock-port slave-from-903 slave
  delay-req interval -4
  sync interval -5
  sync one-step
  transport ipv4 unicast interface Lo1588 negotiation
  clock source 192.168.222.222
ptp r-dti 20
 ptp-domain 0
 clock-port 22
   ethernet 1
   clock source ip 192.168.222.222 gateway ip 93.2.40.93
ns-cBR-05#sho ru
ns-cBR-05#sho running-config | sec prd
ns-cBR-05#
ns-cBR-05#sho running-config | sec rpd
  virtual-arpd 1
    source-id 1
    nc 3.3.3.3 udp-port 100
    ip 32.32.32.32 255.255.255.0
!
cable rpd 1
 identifier 0004.9f00.0919
 no rpd-ds 0 mute
 no rpd-ds 0 shutdown
 core-interface Te1/1/0
  principal
  rpd-ds 0 downstream-cable 1/0/0 profile 128
  rpd-us 0 upstream-cable 1/0/0 profile 4
 r-dti 20
 rpd-event profile 0

ptp clock ordinary domain 0   
 servo tracking-type R-DTI
 clock-port slave-from-903 slave
  delay-req interval -4
  sync interval -5
  sync one-step
  transport ipv4 unicast interface Lo1588 negotiation
  clock source 33.33.158.158
ptp r-dti 1
 ptp-domain 0
 clock-port 22
   ethernet 1
   clock source ip 33.33.158.158 gateway ip 60.10.10.20
 clock-port 23
   ethernet 1
   transport ipv6
   clock source ipv6 2001:10:74:54::1 gateway ipv6 2001:60:10:13::27
== Boot image ==
boot harddisk:cbrsup-universalk9.BLD_V166_THROTTLE_LATEST_20170518_032244_2.SSA.bin

CRDC-NG-E09#dir harddisk:d31_sreg_nightly.cfg