查看“Cisco ios命令”的源代码

== 使用MD-splitting(haofan做得)后，让RPD ipv4/6上线的配置 ==
=== IP 4配置 ===
* multicast pool
<source lang="shell">
# 要让v4上线，multicast pool只能配 v4地址
CRDC-NG-E09#sh run | s multicast pool 62
cable depi multicast pool 62
 ip address 239.1.1.0 255.255.255.0
</source>
* downstream controller-profile （跟multicast pool关联）
<source lang="shell">
cable downstream controller-profile 1
 multicast-pool 62
 max-ofdm-spectrum 192000000
 rf-chan 0 31
  type DOCSIS
  qam-profile 1
  frequency 453000000
  rf-output NORMAL
  docsis-channel-id 1
 rf-chan 158
  docsis-channel-id 162
  ofdm channel-profile 25 start-frequency 807000000 width 192000000 plc 963000000
  qam-profile 1
</source>
=== IP 6配置 ===
* multicast pool
<source lang="shell">
# 要让v6上线，multicast pool只能配 v6地址
CRDC-NG-E09#show run | s multicast pool 66
cable depi multicast pool 66
 ipv6 address FF3A::8000:0/120
</source>
* downstream controller-profile （跟multicast pool关联）
<source lang="shell">
cable downstream controller-profile 200
 multicast-pool 66
 max-ofdm-spectrum 192000000
 rf-chan 0 31
  type DOCSIS
  qam-profile 1
  frequency 453000000
  rf-output NORMAL
  docsis-channel-id 1
 rf-chan 158
  docsis-channel-id 162
  ofdm channel-profile 25 start-frequency 807000000 width 192000000 plc 963000000
  rpd-ds 0 downstream-cable 7/0/14 profile 200
  rpd-ds 0 downstream-cable 7/0/13 profile 200
</source>

== 一些命令 ==
=== copy image ===
*从NG03上copy EO9 harddisk上的image
<pre>
NG03#copy scp: harddisk:                               
Address or name of remote host [20.6.6.2]? 
Source username [admin]? 
Source filename [cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin]? harddisk:cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin  
Destination filename [harddisk:cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin]? cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin
Password: 
</pre>
=== 监控CPU ===
<pre>
show processes cpu monitor
</pre>
=== debug CBR  ===
show cable  rpd log reverse
=== 查看cable interface ===
<pre>
CRDC-NG-E09#sh run interface cable 7/0/5
Load for five secs: 5%/1%; one minute: 6%; five minutes: 7%
Time source is NTP, 01:15:10.505 PST Tue Dec 19 2017

Building configuration...

Current configuration : 28 bytes
!
interface Cable7/0/5
end
</pre>
=== send break ===
<pre>
send break(在init时候，###后就不行了， 通过ctrl ]  ---->)
rommon 1 > dir harddisk:
Please reset before continuing
rommon 2 > confreg 0
You must reset or power cycle for new config to take effect
rommon 3 >
rommon 3 >
rommon 3 >
rommon 3 > reset
</pre>

== 登入 ==
=== telnet 不使用用户名/密码 ===
<pre>
aaa new-model
aaa authentication login default none
aaa authentication enable default none
</pre>
=== SSH 用户名/密码  ===
<pre>
username lab priv 15 pass 0 lab
ip domain name cisco.com
crypto key generate rsa general-keys label ssh_key modulus 2048
ip ssh rsa keypair-name ssh_key
ip ssh version 2

line vty  0 20
 transport input telnet 
line vty  21 99
 transport input ssh 
</pre>
* C02不起作用
<pre>
crypto key generate rsa usage-keys label qingwyan-ssh-key modulus 768
ip ssh rsa keypair-name qingwyan-ssh-key 
</pre>
== 常见错误 ==
=== 证书错误 ===
<pre>
ERR: LICENSE Config Lock Enforced! Cannot bind profile!

license smart register idtoken YWFkYjljOGQtMzA0Mi00OGZhLWIwNDktNTIyZWQ4ZGQ2OWU4LTE1MjYwNDA2%0AMTM3MDl8d3JFRHozZmsyOGZweEhNeUV4N3NkSGZGU3pmN0Y2ZEcvRGFUN09L%0AZy9kdz0%3D%0A  force

show license status

删除下面文件， reload TB就OK了
rm /csl_p/*info

license smart deregister
</pre>

== 杂七杂八 ==
=== 替换running config ===
<pre>
C02#copy harddisk:qingwyan_20171204.cfg startup-config
Destination filename [startup-config]?
14198 bytes copied in 0.777 secs (18273 bytes/sec)
Router#reload
Proceed with reload? [confirm]
</pre>

=== C02 换image ===
==== 0x2的方式 ====
<pre>
telnet 80.3.1.12
C02(config)#no boot system
C02(config)#boot system harddisk:cbrsup-universalk9.BLD_POLARIS_DEV_LATEST_20171123_002433.SSA.bin
C02(config)#config-register 0x2
C02(config)#end
C02#wr
</pre>


[[category: cisco]]