“Cisco ios命令”的版本间的差异
来自qingwei personal wiki
| （未显示同一用户的1个中间版本） | |||
| 第117行： | 第117行： | ||
crypto key generate rsa usage-keys label qingwyan-ssh-key modulus 768 | crypto key generate rsa usage-keys label qingwyan-ssh-key modulus 768 | ||
ip ssh rsa keypair-name qingwyan-ssh-key | ip ssh rsa keypair-name qingwyan-ssh-key | ||
| + | </pre> | ||
| + | == 常见错误 == | ||
| + | === 证书错误 === | ||
| + | <pre> | ||
| + | ERR: LICENSE Config Lock Enforced! Cannot bind profile! | ||
| + | |||
| + | license smart register idtoken YWFkYjljOGQtMzA0Mi00OGZhLWIwNDktNTIyZWQ4ZGQ2OWU4LTE1MjYwNDA2%0AMTM3MDl8d3JFRHozZmsyOGZweEhNeUV4N3NkSGZGU3pmN0Y2ZEcvRGFUN09L%0AZy9kdz0%3D%0A force | ||
| + | |||
| + | show license status | ||
| + | |||
| + | 删除下面文件， reload TB就OK了 | ||
| + | rm /csl_p/*info | ||
| + | |||
| + | license smart deregister | ||
</pre> | </pre> | ||
| 第142行： | 第156行： | ||
[[category: cisco]] | [[category: cisco]] | ||
| − | |||
2018年6月20日 (三) 02:17的最新版本
目录
使用MD-splitting(haofan做得)后，让RPD ipv4/6上线的配置
IP 4配置
- multicast pool
# 要让v4上线，multicast pool只能配 v4地址
CRDC-NG-E09#sh run | s multicast pool 62
cable depi multicast pool 62
ip address 239.1.1.0 255.255.255.0
- downstream controller-profile （跟multicast pool关联）
cable downstream controller-profile 1
multicast-pool 62
max-ofdm-spectrum 192000000
rf-chan 0 31
type DOCSIS
qam-profile 1
frequency 453000000
rf-output NORMAL
docsis-channel-id 1
rf-chan 158
docsis-channel-id 162
ofdm channel-profile 25 start-frequency 807000000 width 192000000 plc 963000000
qam-profile 1
IP 6配置
- multicast pool
# 要让v6上线，multicast pool只能配 v6地址
CRDC-NG-E09#show run | s multicast pool 66
cable depi multicast pool 66
ipv6 address FF3A::8000:0/120
- downstream controller-profile （跟multicast pool关联）
cable downstream controller-profile 200
multicast-pool 66
max-ofdm-spectrum 192000000
rf-chan 0 31
type DOCSIS
qam-profile 1
frequency 453000000
rf-output NORMAL
docsis-channel-id 1
rf-chan 158
docsis-channel-id 162
ofdm channel-profile 25 start-frequency 807000000 width 192000000 plc 963000000
rpd-ds 0 downstream-cable 7/0/14 profile 200
rpd-ds 0 downstream-cable 7/0/13 profile 200
一些命令
copy image
- 从NG03上copy EO9 harddisk上的image
NG03#copy scp: harddisk: Address or name of remote host [20.6.6.2]? Source username [admin]? Source filename [cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin]? harddisk:cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin Destination filename [harddisk:cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin]? cbrsup-universalk9.2017-11-21_05.39_peili2.SSA.bin Password:
监控CPU
show processes cpu monitor
debug CBR
show cable rpd log reverse
查看cable interface
CRDC-NG-E09#sh run interface cable 7/0/5 Load for five secs: 5%/1%; one minute: 6%; five minutes: 7% Time source is NTP, 01:15:10.505 PST Tue Dec 19 2017 Building configuration... Current configuration : 28 bytes ! interface Cable7/0/5 end
send break
send break(在init时候，###后就不行了， 通过ctrl ] ---->) rommon 1 > dir harddisk: Please reset before continuing rommon 2 > confreg 0 You must reset or power cycle for new config to take effect rommon 3 > rommon 3 > rommon 3 > rommon 3 > reset
登入
telnet 不使用用户名/密码
aaa new-model aaa authentication login default none aaa authentication enable default none
SSH 用户名/密码
username lab priv 15 pass 0 lab ip domain name cisco.com crypto key generate rsa general-keys label ssh_key modulus 2048 ip ssh rsa keypair-name ssh_key ip ssh version 2 line vty 0 20 transport input telnet line vty 21 99 transport input ssh
- C02不起作用
crypto key generate rsa usage-keys label qingwyan-ssh-key modulus 768 ip ssh rsa keypair-name qingwyan-ssh-key
常见错误
证书错误
ERR: LICENSE Config Lock Enforced! Cannot bind profile! license smart register idtoken YWFkYjljOGQtMzA0Mi00OGZhLWIwNDktNTIyZWQ4ZGQ2OWU4LTE1MjYwNDA2%0AMTM3MDl8d3JFRHozZmsyOGZweEhNeUV4N3NkSGZGU3pmN0Y2ZEcvRGFUN09L%0AZy9kdz0%3D%0A force show license status 删除下面文件， reload TB就OK了 rm /csl_p/*info license smart deregister
杂七杂八
替换running config
C02#copy harddisk:qingwyan_20171204.cfg startup-config Destination filename [startup-config]? 14198 bytes copied in 0.777 secs (18273 bytes/sec) Router#reload Proceed with reload? [confirm]
C02 换image
0x2的方式
telnet 80.3.1.12 C02(config)#no boot system C02(config)#boot system harddisk:cbrsup-universalk9.BLD_POLARIS_DEV_LATEST_20171123_002433.SSA.bin C02(config)#config-register 0x2 C02(config)#end C02#wr
